How To Calculate The Tension Value Of Belt Conveyor
Sep 30, 2020
With the multifunctional design of modern belt conveyors, the application of mechanical equipment with long distances and large volumes has become more and more extensive. The longer the transportation distance, the higher the belt strength required. However, high-strength belts are not only expensive, but also unstable in quality. Therefore, belt conveyor manufacturers reduce the maximum tension value of the belt in the design, so that the selection of the belt is based on domestic.
At present, the commonly used method to reduce the maximum tension of the belt is power-assisted drive. There are two methods, one is linear friction drive, and the other is reloaded multi-point drive. Both power-assisted drives can significantly reduce the maximum working tension of the belt. The use of reprinted multi-point drive will bring a series of design and calculation difficulties. It includes how to determine the number and location of intermediate driving points and how to calculate belt tension. Combining my design practice, we discuss the calculation of belt tension and the determination of the number of driving points and positions when using reloading multi-point driving.
The setting of the intermediate driving point sets several intermediate driving points. How to arrange the intermediate driving points requires consideration of many factors, including the range of belt selection, the selection of motors, reducers and hydraulic couplings or other driving components, and the limitation of driving point settings Conditions, the overall layout of the belt conveyor, etc. For belt conveyors under different working conditions, there will be different constraints, so it is difficult to propose a universal method for determining the intermediate driving point for belt conveyors under any working conditions. Only the method of determining the position and number of intermediate driving points from the perspective of belt selection is proposed here.
The power range of the intermediate driving point can be seen from the actual situation of the belt. When the strength of the steel cord core belt in our country is below 0 N/mm, its quality is stable and comparable to imported belts. In addition, the price of steel cord belts increases with the increase of belt strength. Therefore, the selection of the control belt is in the range of 0 N/mm and below, which is more advantageous in both technical and economic aspects. If the belt strength of the control belt is 0 N/mm and the belt safety factor k=8, the maximum tension of the belt (unit width) should be 394 N/mm. Because the maximum belt tension appears at the approach point of the driving drum, the driving circumferential force of the driving unit is the difference between the tension at the approach point and the exit point of the belt on the driving drum, which is calculated by the driving power formula of the driving unit: and the Euler formula : Available: where N―――driving total power, kW v――belt running speed, m/s P―――driving circumferential force, N "Lifting and Conveying Machinery" 2000 (9)-belt trend Entry point tension, N――belt running-off point tension, Nμ――coefficient of friction between the belt and drum α――the belt wrapping angle on the drum When the drive unit is driven by a single drum, the wrapping is generally taken The angle is =2.7 (take μ=0.3). The bandwidth of the steel core belt can be obtained under this condition. The power range is 782~1095 kW. If double drum drive is adopted, the belt wrap angle on the drum can reach =3.9. Under this condition, the power range of each driving point It is 923 to 1640 kW. Therefore, when considering the number of driving points, it can be roughly determined according to the above-mentioned power range.
1. Method for determining the intermediate driving point After determining the number of intermediate driving points according to the above power range, according to the belt conveyor design principle, there are the following methods for determining the position of the driving point.
(1) Equal circular force method This method is to evenly distribute the total driving circular force according to the number of driving units. Each driving unit provides the same driving power. It is characterized by a single selection of driving unit equipment, easy maintenance and spare parts preparation. After the driving force of the driving unit is determined, the belt tension depends on the location of the driving unit and the conveyor belt manufacturer. There are two kinds of intermediate driving point layout methods under the condition of equal circumferential force: fixed distance layout method: This method is to divide the conveyor into several sections according to the given distance according to the length of the belt conveyor, and each drive unit drives the corresponding length Section. When the conveyor arrangement is as simple as a single inclination angle, the drive units can be arranged equidistantly. Because the distance of the drive unit is known in this arrangement method, the running and lifting resistance of each section is easy to calculate, so the design calculation is simple. The disadvantage is that the maximum tension of the belt in each drive section may be different, and the belt selection must be determined according to the maximum tension, which may not be able to give full play to the potential of the belt. In addition, the actual wrap angle of each drive unit is quite different, and the wrap angle must be checked in the calculation.
Equal tension arrangement method: The idea of this method is to make the tension of the approach point of each drive unit drum (that is, the maximum tension of each drive section) the same, so that the several peaks in the belt tension diagram are equal, and the belt capacity can be maximized . In the calculation, because the position of the driving point is not known, the running and lifting resistance of each section of the belt cannot be obtained in advance, and the corresponding tension equal equation needs to be supplemented. Assuming n intermediate driving points, n equations with equal tensions need to be supplemented. When there are more driving points, the calculation is more troublesome.
(2) Equal wrapping angle method When the drive unit is arranged according to the equal circumferential force method, the wrapping angle of the belt on the drive drum cannot be controlled. Checking the calculation results of this arrangement method, it is found that the effective wrap angle of a certain drive unit of some conveyors is only tens of degrees, and most of the belt wraps on the drum are spare arcs, which are not fully utilized. Different from the equal circle force method, the idea of the equal wrap angle method is to make the most of the wrap angle of the belt on the drum. When the equal wrap angle method is used, the circumferential force of each drive unit may be different. The equal wrap angle method also has two layout methods: fixed distance layout and equal tension layout.






